LSN2-T/30-D12-C【PDF 12/16 页】CONV DC/DC 150W 30A 0.8-5V SIP

您好，
买卖IC网欢迎您。
请登录
免费注册

8页 9页 10页 11页 [12页]13页 14页 15页 16页

LSN2-T/30-D12 Series

DOSA-SIP, 30A POL DC/DC Converters

[10] Any external capacitance added to the converter’s output may affect ramp

up/down times and ramp tracking accuracy.

Pre-Biased Startup

Newer systems with multiple power voltages have an additional problem

besides startup sequencing. Some sections have power already partially

applied (possibly because of earlier power sequencing) or have leakage power

present so that the DC/DC converter must power up into an existing voltage.

This power may either be stored in an external bypass capacitor or supplied by

an active source.

This “pre-biased” condition can also occur with some types of program-

mable logic or because of blocking diode leakage or small currents passed

through forward biased ESD diodes. Conventional DC/DCs may fail to start up

correctly if there is output voltage already present. And some external circuits

are adversely affected when the low side MOSFET in a synchronous recti?er

converter sinks current at start up.

The LSN2-T/30-D12 series includes a pre-bias startup mode to prevent

these initialization problems. Essentially, the converter acts as a simple buck

current. If the resistive load starts successfully, you may be trying to drive an

external pre-biased active source.

It may also be possible to use pre-bias and sequencing together if the Pre-

Bias source is in fact only a small external bypass capacitor slowly charged by

leakage currents. Test your application to be sure.

Output Adjustments

The LSN2-T/30-D12 series includes a special output voltage trimming feature

which is fully compatible with competitive units. The output voltage may be

varied using a single trim resistor from the Trim input to Power Common.

As with other trim adjustments, be sure to use a precision low-tempco resis-

tor (±100ppm/°C.) mounted close to the converter with short leads. Also be

aware that the output voltage accuracy is ±1.5% (typical) therefore you may

need to vary this resistance slightly to achieve your desired output setting.

Use short leads. Mount the leads close to the converter.

Resistor Trim Equation

converter until the output reaches its set point voltage at which time it converts

to a synchronous recti?er design. This feature is variously called “monotonic”

R TRIM (Ω) =

1200

V O ? 0.80

? 100

because the voltage does not decay (from low side MOSFET shorting) or

produce a negative transient once the input power is applied and the startup

sequence begins.

Don’t Use Pre-Biasing and Sequencing Together

Normally, you would use startup sequencing on multiple DC/DCs to solve the

Pre-Bias problem. By causing all power sources to ramp up together, no one

source can dominate and force the others to fail to start. For most applications,

do not use startup sequencing in a Pre-Bias application, especially with an

external active power source.

If you have active source pre-biasing, leave the Sequence input open so

that the output will step up quickly and safely. A symptom of this condition is

repeated failed starts. You can further verify this by removing the existing load

and testing it with a separate passive resistive load which does not exceed full

Where V O is the desired output voltage.

Figure 14. Trim Connections

www.murata-ps.com/support

MDC_LSN2-T/30-D12 Series.C01 Δ Page 12 of 16

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

我的联系方式

*

*

*

相关PDF资料

LSS-T/10-W12-C CONV DC/DC 60W 10A .6-6V SIP

LTM4600HVIV#PBF IC DC/DC UMODULE 10A 104-LGA

LTM4600IV#PBF IC DC/DC UMODULE 10A 104-LGA

LTM4601AHVEV#PBF IC DC/DC UMODULE 12A 133-LGA

LTM4601AIY#PBF IC DC/DC UMODULE 12A 133-BGA

LTM4602IV#PBF IC DC/DC UMODULE 6A 104-LGA

LTM4603HVEV#PBF IC DC/DC UMODULE 6A 118-LGA

LTM4603IV#PBF IC DC/DC UMODULE 6A 118-LGA

相关代理商/技术参数

LSN2-T/30-D12G-C 功能描述:DC/DC转换器 12Vin 0.8-5Vout 30A 150W Power Good Out RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

LSN2-T/30-D12N-C 功能描述:DC/DC转换器 12Vin 0.8-5Vout 30A 150W Neg polarity RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

LSN2-T/30-D12NG-C 功能描述:DC/DC转换器 12Vin 0.8-5Vout 30A 150W PowerGood NegPl RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

LSN2-T/6-C 制造商:CANDD 制造商全称:C&D Technologies 功能描述:Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters

LSN2-T/6-D12 制造商:CANDD 制造商全称:C&D Technologies 功能描述:Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters

LSN2-T/6-D12-C 功能描述:DC/DC转换器 19.8W 12V/0.75-5V 6A RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

LSN2-T/6-D12G-C 功能描述:DC/DC转换器 19.8W 12V/0.75-5V 6A RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:

LSN2-T/6-D12N-C 功能描述:DC/DC转换器 19.8W 12V/0.75-5V 6A RoHS:否制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: